Camshaft Kit, BEW Franko6 Stage II Deluxe

Description

Franko6 Stage II Deluxe camshaft kit for VW TDIs with BEW engines. This kit is designed to include everything that should be replaced when the camshaft is replaced. It includes a complete stage II camshaft kit, a complete timing belt kit, and a complete oil change and service kit.

Franko6 designed this camshaft and remachined the cam bearings to eliminate known oiling and wear issues with the factory parts. They significantly improve oil flow to better dissipate heat and reduce wear. The camshaft has been chrome-plated for a smoother, harder finish. This camshaft, used properly, has noticeably greater longevity than a factory camshaft. This BEW camshaft is often used in engines with a BHW or BRM engine code due to its further increased reliability over the camshafts traditionally designed for those engines.

Kit Includes:

Stage II Camshaft Kit
Franko6 Stage II BEW Chrome Plated Camshaft — 038109101R-T
8x OEM INA Black Lifters (Nitride Coated) — 038109309C
10x Frank06 Modified Cut Bearings — 038103673BGLB
10x Journal Cap Bolts — 038103714 (Non-stretch, torque to 144 lb/in)
8x Injector Rocker Bolts — 038103714A (Non-stretch, torque to 30 lb/ft)
Camshaft Seal — 068103085E(A)
OEM Tandem Pump Gasket — 038145215
Joe Gibbs Break In Kit with Assembly Lube

Deluxe Timing Belt Kit
OEM Timing Belt — 038109119P
Contitech OEM Serpentine Belt — 6DPK1195
OEM Tensioner — 038109243M
Reinz Camseal — 068103085E(A)
OEM Roller — 038109244J
Metal Impeller Water Pump (usually Graf) — 038121011G
1.5L OEM G12++ Coolant
Deluxe BEW Timing Belt Bolt Kit:

• 1x Engine Bracket Bolt Long — N10328001
• 2x Engine Mount to Body — N10516701
• 2x Engine Mount to Bracket Bolt — N10209605
• 2x Engine Bracket Bolt Short — N90712401
• 1x 8mm Lock Nut for Roller — N01508311
• 1x 8mm Lock Nut for Tensioner — 038109454A

Deluxe Oil Change and Service Kit
5L Pentosin HpII 505.01 Spec Engine Oil
2x Oil Filter — 074115562
Cabin Filter — 1J0819644
Cold Region Air Filter — J0129620A
Fuel Filter — 1J0127401A

Fits the Following:
2004-2006 VW Golf TDI
2004-2005 VW Jetta TDI (not late 2005.5)
2004-2006 VW New Beetle TDI

Warranty Note: This camshaft comes with a 3-year, unlimited mileage warranty against manufacturer defects. Franko6 requires that the camshaft be used only with the modified cam bearings and broken in with the Joe Gibbs Break In oil included in this kit. Documented oil changes must be performed at 10k mile intervals using either of of the following VW 505.01 spec products: Liquimoly TopTec 4100 or Pentosin HPII.
Franko6 requires photographic documentation with any warranty requests, and reserves the right to inspect the camshaft (in some cases the complete cylinder head) to determine the cause of failure prior to any warranty approvals.

Installation Note: Proper break in of a camshaft is essential for proper functioning and longevity. Joe Gibbs Break-in oil facilitates that well. Below is the recommended process.
1. Put assembly lube on all lobes, lifter faces, distributor gears, bearing journals, lifter barrels, and oil pump gears.
2. Turn the engine over by hand to make sure that nothing is binding up (e.g. cam bearings are properly seated) and that timing is correct.
3. Rev engine to 2000-3000 RPM for 20-30 minutes. Drain break-in oil, don’t change the filter.
4. Refill with break-in oil and drive normally for about 500 miles.
5. Drain oil again and replace the filter and oil, using proper VW 505.01 spec oil such as Pentosin HPII or Liquimoly. A bottle of ZDDP additive can provide further protection.

Writeup on the cut cam bearings, including installation tips.

Note on Torsion: Use only the following torque spec.
Journal cap bolts – 038 103 714 — Special Non-stretch torque to 60, 120, 144 inch/lb – Strike caps between each torque & be VERY Careful!
Injector rocker bolts – 038 103 714 A — Special Non-stretch torque to 25 lb/ft